Guillotine & handling - BaumannWohlenberg

T: +44 (0)843 289 3410 - E: webenquiries@friedheim.co.uk    

BaumannWohelenberg – Guillotines and handling equipment

Guillotines

  • Available in six cutting widths (80-225 cm)
  • Advanced touch screen control
  • Extreme precision
  • Excellent safety features

Pile hoists

  • Design of platform aids preparation
  • Finishing functions aided by platform design
  • Reduced liability of injuries due to lifting

Joggers

  • Variety of formats and pile heights available
  • Design ensures minimal use of floor space
  • Pneumatically driven air expulsion
Epsilon - Label System

All companies, who process large cutting volumes of paper- or IML-labels need a fail-safe high-quality cutting solution. The BaumannWohlenberg Epsilon label system, in combination with an ATLAS 1110 made by BLUMER AG (Switzerland), is perfectly suited to meet these requirements.

Components 

Baumann BSH 3-1200 Pile Hoist

BZW Scale Counter

  • Simultaneous jogging and counting

 

Baumann BSB 3 L Automatic Jogger

  • NEW Increased inclination during the jogging process
  • Quicker preparation of an accurately aligned ream

 

Baumann BPS 3 Pressing-Station

  • Removing the remaining air from between the sheets
  • Increased cutting-accuracy

 

Baumann BFS Gripper Transport System 

  • Automatic ream transfer from BSB 3 L towards BPS 3 and then on to the rear-table of the cutter

 

Wohlenberg 132 High-Speed Cutter 

  • Effective cutting process, automatic edge trim. 
  • NEW. When producing labels, it used to be necessary to carry out a complete four-side-trim within the automatic cutter, before cutting the ream into strips. In combination with the new ATLAS 1110 from BLUMER this is no longer necessary.

 

ATLAS-1110 – Strip cutting, punching and banding labels

Possible label formats: from 25 x 45 mm to 170 x 215 mm


Omega Jogging System

The Omega offline jogging system is a central jogging station, which is used for the offline material preparation of paper- or IML-labels. It can of course also be used for job printing works. The system works completely automatically.

Components

BASA 3

  • Completely automatic destacking
  • Completely automatic jogging process
  • Completely automatic pile exchange
  • Completely automatic rejection of the emptied pallet
  • Counting unit (© GTS GmbH)

 

Cardboard-inserter

  • Automatic insertion of intermediate cardboards
  • A gripper transport system transfers the ream from the jogging-table to the alignment-table

 

BA 3 Z Unloader (New Design) NEW

  • Integrated gripper transport system
  • Chip inserter / air-board inserter
  • Accurate restacking of the jogged reams

 

Available for formats: Up to 740 x 1070 mm

 

Guillotines – High speed cutting

 

Sizes: 92, 115, 132, 168, 225

BaumannWohlenberg high-speed guillotines of the pro-tec product line are of solid construction and suited for processing various materials, as e.g. paper, cardboard, offset printing plates or similar cutting stock. Modern cutting technique allows rational cutting of different products and sizes.

The guillotine can be economically used as stand-alone unit or integrated in cutting systems. Program generation is menu-guided and covers a variety of cutting jobs, e.g. Single cut, Program cut, Repeat cut, Clamping without cut, Automatic actual-value transfer.

Advantages*

  • CIP Data module standard
  • 19” touch screen display 16:10 with no additional keys
  • Short stop function for the clamp standard – faster cut cycle
  • Clamping without cut
  • Electronic hand wheel for the back-gauge positioning
  • Stainless steel plated machine table, without slot
  • Pressing cylinder for the clamp is installed centrally underneath the cutting table, providing an equal pressure
  • Programmable clamp pressure standard
  • Automatic adaption of clamp pressure to cutting width
  • Cast iron machine frame in one piece
  • Important options
  • Automatic waste removal ASE, lowers up to 4 mm for collection of small cuts on thin boards
  • Turning and swivel back-gauge
  • Prepared for automatic turning and cutting
  • Linear back-gauge drive for rear table loading
  • *Note: some features and advantages are not available on smaller size machines.

Baumann BSH - Pile Hoists with platform.

The automated functions relief the operator’s physical strain while increasing the efficiency of the high-speed cutter.

Features

  • Piles are lifted and lowered hydraulically
  • A double chain guarantees the highest possible safety
  • The platform has a beveled front-edge so that even large formats can easily be loaded onto the platform (loading with a pallet truck is possible)
  • An adjustable photo-cell verifies constantly that the top of the pile remains always on working-height
  • Castors for mobility

 

Advantages

  • Increase in productivity
  • Decrease or elimination of injuries due to lifting
  • Precise re-stacking

 

Options

  • With adjustable angle stop for unloading

Baumann BSB L – Automatic jogger

All model "L" automatic joggers are equipped with a pneumatic air-expulsion roller with clamping device. Suitable for B2, B1 and B0 formats.

Features

  • The table of the automatic jogger is designed with a stainless steel air-table
  • Side flap with pneumatic tilt
  • Tilt-able both left and right
  • Variable jogging intensity
  • The speed of the air-expulsion roller can be varied to suit different materials
  • Air expulsion can be selected for one or two times

 

Options

  • Pneumatic attachable sheet divider for smaller sheets
  • Cut outs for grippers to automatically remove lifts
  • Unloading through the back after air expulsion
  • Ream stabilizer
  • Count by weight scale mounted under the automatic jogger

 

Advantages

  • Highly accurately aligned layers
  • Increase in productivity

 

Baumann BSB 3 L professional – Automatic jogger

The new BSB 3 L professional is able to jog even "difficult" materials, such as metallic paper, pharmaceutical package inserts or labels, much easier and thus quicker than conventional joggers. Suitable for B1 format

Features

  • Additional aeration during the jogging process
  • Margin-free air expulsion
  • Highly planed and micro-perforated table surface
  • Micro-perforated side gauges
  • New, powerful jogging motor
  • New air expulsion roller for very high pressure
  • Layer stabiliser

 

Baumann BSB e - Reliable jogging system with purely manual positioning. Suitable for B2 format

Features

  • Very smooth surface, micro-perforated air-table-surface
  • Strong jogging motor for a quick and precise alignment of the reams
  • Extreme inclination for right- and left lay, step-less adjustment
  • Easy manual operation of the two side gauges
  • Selector switch for the table air
  • Selector switch for the vibrating motor
  • No compressed air required
  • Sturdy 3 pillar construction
  • Low maintenance
  • No set-up times

Baumann BA N e - Semi-automatic re-stacking of single- and multiple cuts with high precision.

Most important features:

  • Very smooth surface, micro-perforated air-table-surface
  • Very lean table construction with a long slope
  • Thanks to the very limited drop height at the transfer to the pallet, even very small cuts can be re-stacked with ease
  • Precise guides
  • Sturdy and strong design and engineering
  • No compressed air required
  • The pallet can be removed from either side
  • Low maintenance
  • No set-up times
  • Maximises energy savings

 

Baumann BA N - Unloaders for piles ≤ 1100 mm

The ergonomic and economically effective way to restack single and multiple cuts with high precision. The manual re-stacking of paper and cardboard after the cutting-process requires a lot of time and effort. The unloader gives you the opportunity to automate the restacking process. Unloaders BA N take up the material at the level of the table. The pile is positioned underneath the unloader table. The reams are re-stacked until a maximum pile height of 1100 mm has been reached. Unloaders BA N can either be installed on the right or on the left hand-side of the cutter. The design is very innovative (especially the principle of controlled axis), material and finish are of high-quality. The user friendly operators panel with clear text display offers the opportunity to change all relevant parameters.

Advantages

  • Increased productivity
  • Very good re-stacking results
  • Careful material handling
  • Latest technology

 

Baumann BA - Unloader

The ergonomic and economically effective way to re-stack single and multiple cuts with high precision. The manual re-stacking of paper and cardboard after the cutting-process requires a lot of time and effort. The unloader gives you the opportunity to automate the re-stacking process. Unloaders type BA are especially made for pile-heights of up to 1400 mm. The material is re-stacked in front of the unloader. The material is taken up at the level of the table and re-stacked either above or under this level. Unloaders BA can either be installed on the right or on the left hand-side of the cutter.  The design is very innovative (especially the principle of controlled axis), material and finish are of high-quality. The user friendly operator’s panel with clear text display offers the opportunity to change all relevant parameters.

Advantages

  • Increased productivity
  • Very good re-stacking results
  • Careful material handling
  • Latest technology
  • Maximises energy savings

Baumann BSW - Automatic pile turners

The manual handling of paper and cardboard-stacks is a backbreaking and expensive process. Baumann Pile Turners give you the opportunity to save time, reduce the costs and eliminate the physical effort. There is a great variety of requirements today’s pile turners have to meet.

A diversity of tasks can be carried out by these multiple machines:

  • Pile turning
  • Precise pile alignment
  • Accelerate the drying process of printed products
  • Aerate and thus separate sheets prior to the printing process
  • Pallet exchange
  • Remove wastepaper
  • Centre a pile on the top of a system pallet
  • Integration into a logistic system, etc.

 

Baumann has concentrated on this diversity of tasks and offers a very broad range of pile turners in order to put the perfect pile turner for any task at our customers disposal. The automated pile turners are equipped with an operator’s panel with a clear text display, which can be delivered with a touch screen, if desired. According to the model, up to 9 different programs can be selected by the operator. The automated process is started when the program is started. The operator can adjust the program and optimize the process without having to interrupt the program.

Essential functions

  • Aeration with powerful blowers and broad air-nozzles, which can be closed for smaller formats. The aeration process can be adjusted at the operator’s panel
  • Adjustable vibration with alignment-stop, which is extended automatically
  • Motorized and fully automatic pile turning
  • Safety devices (safety-fence and safety-light barrier at the entrance)

 

Advantages

  • Comfortable operation
  • Solid and compact construction
  • A great variety of possible applications
  • Excellent cost-benefit ratio

 

Baumann BSW - Semi-automatic pile turners

The manual handling of paper and cardboard-stacks is a backbreaking and expensive process. Baumann Pile Turners give you the opportunity to save time, reduce the costs and eliminate the physical effort. There is a great variety of requirements today’s pile turners have to meet.

A diversity of tasks can be carried out by these multiple machines:

  • Pile turning
  • Precise pile alignment
  • Accelerate the drying process of printed products
  • Aerate and thus separate sheets prior to the printing process
  • Pallet exchange
  • Remove wastepaper
  • Centre a pile on the top of a system pallet

 

Baumann has concentrated on this diversity of tasks and offers a very broad range of pile turners in order to put the perfect pile turner for any task at our customers disposal.

  • Semi-automatic processes make the operation of the semi-automated pile turners very comfortable:
  • Aeration with powerful blowers and broad air-nozzles, which can be closed for smaller formats
  • Vibration with adjustable alignment-stop, which is extended automatically (apart from BSW 2)
  • Manual or motor supported pile turning

 

Advantages

  • Comfortable operation
  • Solid and compact construction
  • Fast and reliable
  • High quality
  • Excellent cost-benefit ratio

The Baumann BASA, in its different formats, is believed to be the first system worldwide that is able to align a large variety of materials fully automatically! The BASA is equipped for two different modes of operation:

During automatic operation, the machine processes the arriving pile without any operator assistance and provides the jogged and aligned layers in the desired height for further processing.

For critical materials and smaller tasks the machine has been provided with a manual operating mode that works similar to a traditional jogger.

The Baumann BASA offers touch screen simplicity of operation, as well as both in-line and off-line solutions. The machine can handle all types of papers (over 60 gsm), various types of label papers, cardboard (up to 300 gsm), foils, certain types of plastics, and perforated and embossed paper and cardboard.  BASA options include a carton inserter and a counting device.

Friedheim International Ltd, Park House, Park Lane,
Hemel Hempstead, HP2 4TT
Tel: +44 (0) 1442 206100 | Fax: +44 (0) 1442 206101